[Wickyup2]

On the rock sliders, I was thinking maybe we can reuse the top portion of the plastic molding by attaching it to some sort of fixture and rip saw off that bottom lip and some how reattaching it over the top portion of the rock slider inside the door areas to cover the screws for a better finished look

 

[Sgt_Strife]

Two thumbs up for Rocky Road !!!Easy to install !! Everything lines up perfect!'
Disregard the RR insructions , they are useless
Just remove the 2 Bolts holding up each hook, slide the mount in between the hook and top , line up the holes,put back the bolts but don't tighten them , the hooks may push back some ,so you have to pull them back forward by putting a strap on the hooks ,rap the strap around tree ,back up pulling the hooks forward , then tighten the bolts .....done!! Next attach the skid plate and that's Easy too just 4 bolts .2 on top ,2 on bottom... Done

Did you have to trim plastic to get the bumper to slide in. It looks like i may have to take a drumel to create more clearance for the bumper to slide in over the hooks.

I put the sliders on last night and had to go to the store to buy more hardware that wasn't included in the kit. I also broke a couple flare clips trying to pull off the OEM cover panels and need to find a place that sells them.
Thx for your time

Here is a thread I started about trim fasteners. You'll find a source in there.

http://www.jeeprenegadeforum.com/fo...ube.html#/forumsite/21080/topics/44546?page=2

 

[Wickyup2]

Finished winch mount

 

[Sgt_Strife]

Finished winch mount

Yea buddy!

I just used mine tonight. All lights on looks sick!

P.S. I had to use a few washers in order to get my warn lights to point down to a decent level.

 

[Mrsig]

Guys it looks great on your Jeeps. Any one know if it will work on a non TH?

 

[Sgt_Strife]

Guys it looks great on your Jeeps. Any one know if it will work on a non TH?

The skid plate definitely won't. But you'd have to check to see if you have the same mounting points where the TH hooks are. If so, then it's about clearance between the facia and the winch mount.

I'm pretty doubtful that it will.

 

[txjeeper35]

Here is a thread I started about trim fasteners. You'll find a source in there.

http://www.jeeprenegadeforum.com/fo...ube.html#/forumsite/21080/topics/44546?page=2

This linked to a short thread about an a/c drain??

I was doing my drilling of holes to mount my rock rails up, and of course broke a few front fender clips, attempting to relocate a couple clips from high to low on the fenders, but no cooperation from this **** white clipy thingy... ?? headed to dealer in the AM to hopefully get a bag of clips.. And man that pinch weld is a beast to drill through.. Last step to get my sliders bolted up.

 

[Sgt_Strife]

Here is a thread I started about trim fasteners. You'll find a source in there.

http://www.jeeprenegadeforum.com/fo...ube.html#/forumsite/21080/topics/44546?page=2

This linked to a short thread about an a/c drain??

I was doing my drilling of holes to mount my rock rails up, and of course broke a few front fender clips, attempting to relocate a couple clips from high to low on the fenders, but no cooperation from this **** white clipy thingy... ?? headed to dealer in the AM to hopefully get a bag of clips.. And man that pinch weld is a beast to drill through.. Last step to get my sliders bolted up.

That's odd... Whenever I copy the link it pastes as that a c drainage...

This should work:

http://www.jeeprenegadeforum.com/forum/showthread.php?t=44546

 

[txjeeper35]

Yay thank you Sgt. Ordered a pack of 10 don't wanna drive up north, and don't wanna wait too long.

Gonna try to finish tomorrow with my drilling and attempting to put these clips in. I dislike this design, but the last fender I had to work with was a 98 XJ so j guess it could be that..

 

[Sgt_Strife]

Yay thank you Sgt. Ordered a pack of 10 don't wanna drive up north, and don't wanna wait too long.

Gonna try to finish tomorrow with my drilling and attempting to put these clips in. I dislike this design, but the last fender I had to work with was a 98 XJ so j guess it could be that..

No problem. I'm still rolling around with a loose front left fender piece, because t it's not horrible so I'm fine want ting for my clips.

 

[txjeeper35]

Got my rock rails finally bolted up. That pinch weld is not friendly!! And I only broke 2 drill bits. Not mine, my dads, oops dull bits, but my dewalt bits from HD worked well with no breaks ??

 

[txjeeper35]

???

 

[Sgt_Strife]

Got my rock rails finally bolted up. That pinch weld is not friendly!! And I only broke 2 drill bits. Not mine, my dads, oops dull bits, but my dewalt bits from HD worked well with no breaks ??

Nice job! Any plans to test the out?

 

[Mrsig]

That looks great.

 

[txjeeper35]

Nice job! Any plans to test the out?

I wish I could say yes. It would be a spur of the moment..if I knew somewhere easy and local to go try them out...work too much to plan something, and the lady's schedule doesnt match up to mine, so I cant go for a long time or she'd get a little lonely:crying:

 

[Wickyup2]

Added a KFI rubber winch line stop to protect the fairlead.
$15.95 with shipping from Country Cat.com

 

[Sgt_Strife]

Added a KFI rubber winch line stop to protect the fairlead.
$15.95 with shipping from Country Cat.com

Nice find!

 

[Wickyup2]

With added steel to the seam when adding the rock sliders will the stock jack still fit?

 

[Wickyup2]

That last pic I posted of the jack isn't from the renegade
This is more like it

 

[Sgt_Strife]

That last pic I posted of the jack isn't from the renegade
This is more like it

With added steel to the seam when adding the rock sliders will the stock jack still fit?

I'll have to check it out. I'll let you know.